hasemcan.blogg.se

Keil 5 与 tm4c1231c3pm
Keil 5 与 tm4c1231c3pm







keil 5 与 tm4c1231c3pm
  1. Keil 5 与 tm4c1231c3pm update#
  2. Keil 5 与 tm4c1231c3pm registration#
  3. Keil 5 与 tm4c1231c3pm verification#
  4. Keil 5 与 tm4c1231c3pm software#

TimerConfigure(GPTIMER0_BASE, GPTIMER_CFG_SPLIT_PAIR | GPTIMER_CFG_B_CAP_COUNT | GPTIMER_CFG_A_PERIODIC_UP ) !< GPTIMER_CFG ( Configure Timer for 16 bit Timer ) TimerDisable(GPTIMER0_BASE,GPTIMER_BOTH) IOCPinConfigPeriphInput(BSP_LED_BASE, BSP_LED_1, IOC_GPT0OCP1) SysCtrlPeripheralEnable(SYS_CTRL_PERIPH_GPT0) SysCtrlIOClockSet(SYS_CTRL_SYSDIV_32MHZ) SysCtrlClockSet(false, false, SYS_CTRL_SYSDIV_32MHZ) Inīoth cases, the status flags are cleared by writing a 1 to the CnMCINT bit of the GPTM Interrupt Poll the CnMRIS bit in the GPTMRIS register or wait for the interrupt to be generated (if enabled). Set the TnEN bit in the GPTIMER_CTL register to enable the timer and begin waiting for edge events.ġ0. If interrupts are required, set the CnMIM bit in the GPTM Interrupt Mask (GPTIMER_IMR) register.ĩ. Load the event count into the GPTM Timer n Match (GPTIMER_TnMATCHR) register.Ĩ. Load the timer start value into the GPTM Timer n Interval Load (GPTIMER_TnILR) register.ħ. If a prescaler is to be used, write the prescale value to the GPTM Timer n Prescale RegisterĦ. Configure the type of event(s) that the timer captures by writing the TnEVENT field of the GPTMĥ. In the GPTM Timer Mode (GPTIMER_TnMR) register, write the TnCMR field to 0x0 and the TnMRĤ. Write the GPTM Configuration (GPTIMER_CFG) register with a value of 0x0000.0004.ģ. Ensure the timer is disabled (the TAEN bit is cleared) before making any changes.Ģ. I am going to post the steps and my code for the same.Ī timer is configured to Input Edge-Count mode by the following sequence:ġ. Also followed the steps as mentioned in the data sheet. I would like to use the CC2538 in Input Edge Count mode using Timer for detection of rising edges. I would like to measure a frequency from 500 Khz to 1 MHz. Refer to System Requirements Overview for hardware and operating system requirements.I am giving a rising edge frequency to CC2538 at BSP_LED_1 pin of CC2538.

keil 5 与 tm4c1231c3pm

Keil 5 与 tm4c1231c3pm software#

Updated: NuLink version  with correct access to Flash algorithms from Software Packs. Updated: Segger J-Link driver for ARM devices to version 4.96d that now supports Cortex-M7.

Keil 5 与 tm4c1231c3pm update#

Updated: ULink2 Firmware version update to 2.03 that fixes a potential problem with USB 3.0 ports. Keil.MDK-Middleware Version 6.2.0 and CMSIS Version 4.2.0.

Keil 5 与 tm4c1231c3pm registration#

The ARM Compiler 5.04u2 for safety critical applications is available from ARM Compiler download area (a registration or login is required). Details can be found in the Compiler specific Release Notes. This MDK release contains ARM Compiler 5.05u1 (build 106). The Event Viewer displays now also timing information for interrupt execution.

Keil 5 与 tm4c1231c3pm verification#

The new debug command SBC allows to control software breakpoints which is for example important for algorithm verification that calculate CRC over a code area. Before the latest version was downloaded.Īt load time of a project the device name can be manually changed when the project was using an obsolete device that no longer available with the current Software Pack. Improved download support for missing Software Packs where a fixed version is selected in the project. This MDK release contains μVision V5.14.0.0.









Keil 5 与 tm4c1231c3pm